Bridjit Curb Ramp for Extra Large Driveway 20ft
The 5 piece set includes a left, 3 center, and right-side sections for driveway entries up to 20′ wide.
Additional center pieces (bought separately) can increase coverage to more than 20ft to accommodate the length of your driveway. All pieces are held together by galvanized bolts measured 1/2″ x 7-1/2″.
The Bridjit curb ramps for cars are used to protect the undercarriages of vehicles such as cars, trucks, and golf carts, as well as facilitate the movement of wheeled carts, hand trucks, or wheel chairs over a curb. These Curb Ramps are not bolted down to the storm gutter, just bolted together, forming a 150lb. to 200lb mass, (depending on the number of sections used).
Check Bridjit Compatibility Criteria before ordering. This curb ramp is made for a very specific type of curb. See the Compatibility Criteria image.
- Money saving solution to replacing your driveway entry, estimated to be from $2500 to $3500.
- Low profile vehicles can now use the driveway without inflicting damage to tires and rims.
- Bridjit driveway ramps help maintain gas mileage by minimizing damage done to steering components and alignment, reducing maintenance costs and tire wear.
- Bridjit is an easy 2 person, 15 minute installation solution, and requires no special tools.
- Can alleviate driver and passenger back pain, experienced while entering and exiting driveways.
- Neighborhood Friendly, Bridjit has a built-in full length waterway allowing normal drainage. The angled ends guide excessive water flows out and around the ramp, assisting in the elimination of debris.
- Sloped ends that ease vehicles up and over the ramp when parking parallel to the curb.
- Can be easily flipped out of the way for periodic cleaning.
- Environmentally “green” product, made from recycled tires.
Read More About Bridjit Curb Ramps
Bridjit Curb Ramp is Eco friendly – The average American contributes 4 tires every year to our landfills. Each BRIDJIT rubber curb ramp set uses 12 passenger tires, thus helping to reduce the number of scrap tires in landfills, making it the Green solution to your jarring curb problem. (There are at least 275 million scrap tires in stockpiles in the U.S.).
BRIDJIT curb ramps are 100% made in the USA.
What are the actual dimensions of each ramp section?
Each section nominally measures 48 in. long x 16 in. wide x 2 3/4 in. thick at the center, tapering to 3/4 thick at the top and bottom.
Will Bridjit Curb Ramp Fit My Curb? Check Bridjit Compatibility Criteria
What joining method is used to keep the BRIDJIT sections together?
BRIDJIT comes supplied with 1/2in. x 71/2in. galvanized bolts, preinserted into the center sections. These bolts need to be driven into the adjoining section as shown in our instruction manual. Friction between the rubber and bolts keep the sections tight together, the supplied nuts are a fail safe step.
How do I determine the number of 4ft. BRIDJIT sections required for my driveway?
The number of 4 ft. sections required depends primarily on the width and depth of your driveway. A 2-car garage, with a driveway less than 2 cars deep, will require more sections, in that you do not have room to maneuver your cars to the center of the driveway opening. These additional sections can be added later, but we recommend a minimum of 4 sections if you have a 2-car garage with less than a 2-car deep driveway or a 3-car garage.
What keeps BRIDJIT in place during use?
BRIDJIT’s weight provides the stability required to keep the device in place, with little or no adjustment required during use. Mechanical fixing to the curb should not be required.
How does BRIDJIT compensate for curved curbing as used in cul-de-sacs?
BRIDJIT was manufactured in 4ft sections to allow for curvature of the curbing. The longer connection bolts allow the device to make the turn, leaving what we believe is an acceptable wedge of space between sections as they fit in place.
How does BRIDJIT allow for flow of water?
BRIDJIT has a full length 2 1/2in. waterway built into the underneath of the product, as well as angled ends which promotes excessive water to flow out and around the device, cleaning out debris.
What effect does exposure to the elements have on BRIDJIT?
BRIDJIT is made from ground up rubber tires and will in time tend to lose it’s luster, turning much the same color as the asphalt street, remaining durable for many years.
What maintenance is required for the BRIDJIT product?
Depending greatly on the amount of construction or maintenance work done around the home or neighborhood, it is suggested that BRIDJIT be periodically flipped up out of the gutter (using two people), the gutter area swept up, and debris properly discarded.
Is street sweeper operation impacted?
We have been testing BRIDJIT for almost 2 years and due to the weight and durability have had no impact by street sweeping machinery.
What happens if someone is driving or parallel parking in the gutter?
We have sloped each end of BRIDJIT to allow easier access up and over the ends. This feature, along with the durability of the rubber material, should eliminate any concern.
How does Bridjit work if I have a storm sewer inlet/grate located within my driveway?
Depending on the exact right to left location of the grate and depth of your driveway Bridjit can still be utilized. You should never place the Bridjit ramp over the top of the grate.